https://www.phoenixcontact.com/pi/products/2903345 07/23/2018???page? 1 ?/? 6 relay module?-?RIF-1-RSC-LV-24AC/2x21au?-?2903345 please be informed that the data shown in this pdf document is generated from our online catalog. please find the complete data in the user's documentation. our general terms of use for downloads are valid (http://phoenixcontact.com/download) pre-assembled relay module with screw connection, consisting of: relay base, multi-layer contact relay, plug- in display/interference suppression module, and retaining bracket. contact type: 2 changeover contacts. input voltage: 24 v ac key commercial data packing unit 10 stk gtin gtin 4046356732789 technical data note utilization restriction emc: class a product, see manufacturer's declaration in the download area dimensions width 16 mm height 89 mm depth 75 mm ambient conditions ambient temperature (operation) -40 c ... 50 c ambient temperature (storage/transport) -40 c ... 85 c coil side nominal input voltage u n 24 v ac input voltage range in reference to u n see diagram mains frequency 50/60 hz typical input current at u n 33 ma typical response time 3 ms ... 12 ms typical release time range 3 ms ... 20 ms cos j reduction factor 1 0,9 0,3 0,4 0,5 0,6 0,7 0,8 0,9 1 0,8 0,7 0,6 0,5 0,4 0,3 0,2 20 30 40 50 60 70 80 1 2 3 4 5 6 7 8 9 10 11 ambient temperature [c] limiting continuous current per contact [a] dc coilac coil 12 22 14 24 11 21 a2 a1 ac, ohmic loaddc, ohmic load, contacts in series dc, ohmic load dc, l/r = 40 ms switching voltage [v] switching current [a] 0,1 0,2 0,3 0,5 1 2 4 6 10 20 10 20 30 50 70 100 300 200 12 3 4 3 1 4 2 cycles switching current [a] 250 v ac, ohmic load (dc coils) 250 v ac, ohmic load (ac coils) 0 1 4 8 12 16 10 7 10 6 10 5 10 4 2 3 5 6 7 11 9 10 151413 12 2 1 0,6 0,7 0,8 0,9 1,0 1,1 1,2 1,3 1,4 1,5 1,6 1,7 1,8 20 30 40 50 60 70 80 ambient temperature [c] coil voltage u/u n dc coilsac coils
https://www.phoenixcontact.com/pi/products/2903345 07/23/2018???page? 2 ?/? 6 relay module?-?RIF-1-RSC-LV-24AC/2x21au?-?2903345 technical data coil side coil voltage 24 v ac protective circuit varistor operating voltage display yellow led contact side contact type 2 pdt type of switch contact single contact contact material agni, hard gold-plated maximum switching voltage 30 v ac 36 v dc minimum switching voltage 100 mv (at 10 ma) min. switching current 1 ma (at 24 v) maximum inrush current 50 ma limiting continuous current 50 ma interrupting rating (ohmic load) max. 1.2 w (at 24 v dc) contact side (with destroyed gold layer) contact material agni note the following values are applicable if a gold layer is destroyed maximum switching voltage 250 v ac/dc minimum switching voltage 5 v (at 10 ma) limiting continuous current 12 a (20 ms, n/o contact) min. switching current 10 ma (at 5 v) interrupting rating (ohmic load) max. 192 w (at 24 v dc) 96 w (at 48 v dc) 60 w (at 60 v dc) 44 w (at 110 v dc) 57 w (at 220 v dc) 2000 va (for 250 v ac) switching capacity in acc. with din vde 0660/iec 60947 2 a (at 24 v, dc13) 0.2 a (at 110 v, dc13) 0.2 a (at 250 v, dc13) 2 a (at 24 v, ac15) 2 a (at 120 v, ac15) 2 a (at 250 v, ac15) connection data input side connection name coil side connection method screw connection stripping length 8 mm conductor cross section solid 0.5 mm2 ... 4 mm2 conductor cross-section solid (2 conductors with same cross section) 0.5 mm2 ... 2.5 mm2 cos j reduction factor 1 0,9 0,3 0,4 0,5 0,6 0,7 0,8 0,9 1 0,8 0,7 0,6 0,5 0,4 0,3 0,2 20 30 40 50 60 70 80 1 2 3 4 5 6 7 8 9 10 11 ambient temperature [c] limiting continuous current per contact [a] dc coilac coil 12 22 14 24 11 21 a2 a1 ac, ohmic loaddc, ohmic load, contacts in series dc, ohmic load dc, l/r = 40 ms switching voltage [v] switching current [a] 0,1 0,2 0,3 0,5 1 2 4 6 10 20 10 20 30 50 70 100 300 200 12 3 4 3 1 4 2 cycles switching current [a] 250 v ac, ohmic load (dc coils) 250 v ac, ohmic load (ac coils) 0 1 4 8 12 16 10 7 10 6 10 5 10 4 2 3 5 6 7 11 9 10 151413 12 2 1 0,6 0,7 0,8 0,9 1,0 1,1 1,2 1,3 1,4 1,5 1,6 1,7 1,8 20 30 40 50 60 70 80 ambient temperature [c] coil voltage u/u n dc coilsac coils
https://www.phoenixcontact.com/pi/products/2903345 07/23/2018???page? 3 ?/? 6 relay module?-?RIF-1-RSC-LV-24AC/2x21au?-?2903345 technical data connection data input side conductor cross section flexible 0.5 mm2 ... 4 mm2 0.5 mm2 ... 4 mm2 (ferrule with plastic sleeve) conductor cross section flexible (2 conductors with same cross section) 0.5 mm2 ... 2.5 mm2 0.5 mm2 ... 1.5 mm2 (twin ferrule with plastic sleeve) conductor cross section awg 20 ... 10 (solid) 20 ... 12 (flexible) torque 0.5 nm ... 0.6 nm connection data output side connection name contact side connection method screw connection stripping length 8 mm conductor cross section solid 0.5 mm2 ... 4 mm2 conductor cross-section solid (2 conductors with same cross section) 0.5 mm2 ... 2.5 mm2 conductor cross section flexible 0.5 mm2 ... 4 mm2 0.5 mm2 ... 4 mm2 (ferrule with plastic sleeve) conductor cross section flexible (2 conductors with same cross section) 0.5 mm2 ... 2.5 mm2 0.5 mm2 ... 1.5 mm2 (twin ferrule with plastic sleeve) conductor cross section awg 20 ... 10 (solid) 20 ... 12 (flexible) torque 0.5 nm ... 0.6 nm general type of note notes on operation note fbs 2-6... plug-in bridge for the input side (a2) and fbs-2-8... plug-in bridge for the output side (11/21) test voltage relay winding/relay contact 4 kv rms (50 hz, 1 min.) test voltage pdt/pdt 2.5 kv rms (50 hz, 1 min.) operating mode 100% operating factor degree of protection ip20 (relay base) rt iii (relay) mechanical service life approx. 10 7 cycles mounting position any assembly instructions in rows with zero spacing standards and regulations standards/regulations din en 50178 rated surge voltage 6 kv insulation safe isolation, basic insulation, and 4 kv rated surge voltage between all changeover contacts. degree of pollution 2 overvoltage category iii flammability rating according to ul 94 v2 cos j reduction factor 1 0,9 0,3 0,4 0,5 0,6 0,7 0,8 0,9 1 0,8 0,7 0,6 0,5 0,4 0,3 0,2 20 30 40 50 60 70 80 1 2 3 4 5 6 7 8 9 10 11 ambient temperature [c] limiting continuous current per contact [a] dc coilac coil 12 22 14 24 11 21 a2 a1 ac, ohmic loaddc, ohmic load, contacts in series dc, ohmic load dc, l/r = 40 ms switching voltage [v] switching current [a] 0,1 0,2 0,3 0,5 1 2 4 6 10 20 10 20 30 50 70 100 300 200 12 3 4 3 1 4 2 cycles switching current [a] 250 v ac, ohmic load (dc coils) 250 v ac, ohmic load (ac coils) 0 1 4 8 12 16 10 7 10 6 10 5 10 4 2 3 5 6 7 11 9 10 151413 12 2 1 0,6 0,7 0,8 0,9 1,0 1,1 1,2 1,3 1,4 1,5 1,6 1,7 1,8 20 30 40 50 60 70 80 ambient temperature [c] coil voltage u/u n dc coilsac coils
https://www.phoenixcontact.com/pi/products/2903345 07/23/2018???page? 4 ?/? 6 relay module?-?RIF-1-RSC-LV-24AC/2x21au?-?2903345 technical data environmental product compliance china rohs environmentally friendly use period = 50 for details about hazardous substances go to tab downloads, category manufacturer's declaration drawings circuit diagram ac coils diagram operating voltage range diagram interrupting rating diagram contact derating cos j reduction factor 1 0,9 0,3 0,4 0,5 0,6 0,7 0,8 0,9 1 0,8 0,7 0,6 0,5 0,4 0,3 0,2 20 30 40 50 60 70 80 1 2 3 4 5 6 7 8 9 10 11 ambient temperature [c] limiting continuous current per contact [a] dc coilac coil 12 22 14 24 11 21 a2 a1 ac, ohmic loaddc, ohmic load, contacts in series dc, ohmic load dc, l/r = 40 ms switching voltage [v] switching current [a] 0,1 0,2 0,3 0,5 1 2 4 6 10 20 10 20 30 50 70 100 300 200 12 3 4 3 1 4 2 cycles switching current [a] 250 v ac, ohmic load (dc coils) 250 v ac, ohmic load (ac coils) 0 1 4 8 12 16 10 7 10 6 10 5 10 4 2 3 5 6 7 11 9 10 151413 12 2 1 0,6 0,7 0,8 0,9 1,0 1,1 1,2 1,3 1,4 1,5 1,6 1,7 1,8 20 30 40 50 60 70 80 ambient temperature [c] coil voltage u/u n dc coilsac coils
https://www.phoenixcontact.com/pi/products/2903345 07/23/2018???page? 5 ?/? 6 relay module?-?RIF-1-RSC-LV-24AC/2x21au?-?2903345 diagram electrical service life diagram service life reduction factor articles in set relay base?-?rif-1-bsc/2x21?-?2900930 rif-1... relay base, for miniature power relay with 1 or 2 changeover contacts or identical solid-state relays, screw connection, plug-in option for input/interference suppression modules, for mounting on ns 35/7,5 ? ? single relay?-?rel-mr- 24ac/21-21au?-?2961464 plug-in miniature power relay, with multi-layer gold contact, 2 pdts, input voltage 24 v ac ? ? plug-in module?-?rif-lv-12-24 uc?-?2900942 plug-in module, for mounting on rif-1, rif-2, rif-3, and rif-4, with varistor and yellow led, input voltage: 12 ... 24 v ac/dc 20 % ? ? retaining bracket?-?rif-rh-1?-?2900953 relay retaining bracket, with ejector function and holder for marking material, suitable for rif-1 relay base, for 16 mm tall miniature power relay and solid-state relay ? ? cos j reduction factor 1 0,9 0,3 0,4 0,5 0,6 0,7 0,8 0,9 1 0,8 0,7 0,6 0,5 0,4 0,3 0,2 20 30 40 50 60 70 80 1 2 3 4 5 6 7 8 9 10 11 ambient temperature [c] limiting continuous current per contact [a] dc coilac coil 12 22 14 24 11 21 a2 a1 ac, ohmic loaddc, ohmic load, contacts in series dc, ohmic load dc, l/r = 40 ms switching voltage [v] switching current [a] 0,1 0,2 0,3 0,5 1 2 4 6 10 20 10 20 30 50 70 100 300 200 12 3 4 3 1 4 2 cycles switching current [a] 250 v ac, ohmic load (dc coils) 250 v ac, ohmic load (ac coils) 0 1 4 8 12 16 10 7 10 6 10 5 10 4 2 3 5 6 7 11 9 10 151413 12 2 1 0,6 0,7 0,8 0,9 1,0 1,1 1,2 1,3 1,4 1,5 1,6 1,7 1,8 20 30 40 50 60 70 80 ambient temperature [c] coil voltage u/u n dc coilsac coils
https://www.phoenixcontact.com/pi/products/2903345 07/23/2018???page? 6 ?/? 6 relay module?-?RIF-1-RSC-LV-24AC/2x21au?-?2903345 articles in set approvals approvals approvals dnv gl / eac ex approvals approval details dnv gl? ? http://exchange.dnv.com/tari/ ?taa000018v eac? ? ? ?ru c- de.a*30.b.01082 phoenix contact 2018 ? - all rights reserved http://www.phoenixcontact.com phoenix contact gmbh & co. kg flachsmarktstr. 8 32825 blomberg germany tel. +49 5235 300 fax +49 5235 3 41200 http://www.phoenixcontact.com cos j reduction factor 1 0,9 0,3 0,4 0,5 0,6 0,7 0,8 0,9 1 0,8 0,7 0,6 0,5 0,4 0,3 0,2 20 30 40 50 60 70 80 1 2 3 4 5 6 7 8 9 10 11 ambient temperature [c] limiting continuous current per contact [a] dc coilac coil 12 22 14 24 11 21 a2 a1 ac, ohmic loaddc, ohmic load, contacts in series dc, ohmic load dc, l/r = 40 ms switching voltage [v] switching current [a] 0,1 0,2 0,3 0,5 1 2 4 6 10 20 10 20 30 50 70 100 300 200 12 3 4 3 1 4 2 cycles switching current [a] 250 v ac, ohmic load (dc coils) 250 v ac, ohmic load (ac coils) 0 1 4 8 12 16 10 7 10 6 10 5 10 4 2 3 5 6 7 11 9 10 151413 12 2 1 0,6 0,7 0,8 0,9 1,0 1,1 1,2 1,3 1,4 1,5 1,6 1,7 1,8 20 30 40 50 60 70 80 ambient temperature [c] coil voltage u/u n dc coilsac coils
|
